Tantrum—怒火

捕风

[ 本帖最后由 捕风 于 2009-2-28 01:44 编辑 ]

捕风

捕风

[ 本帖最后由 捕风 于 2009-2-28 01:46 编辑 ]

捕风

vipersportkite的风筝都不是量产机，很低调，设计师夫妇“貌似”不以此为生，所以真正拥有的人少之又少，资料非常缺乏，所以技术参数里边很多项都留空了，好在有个别细节的图片可以参考下。视频只有一个就是ron在自由女神像下飞的片子（Tantrum built this city），真是遗憾得很。
如果有熟悉这款机子的朋友来补充一下。。(25gif


[ 本帖最后由 捕风 于 2009-2-28 02:16 编辑 ]

捕风

飞翔

我喜欢这张：(16gif

jacky

这是一个在世界上NO、1的风筝制作室、版主说得很对、是夫妇制作室是非常低调、我非常想得到他们夫妇所制作的《眼晴蛇》。这款作品、我找了一些国外的朋友也问、没有声音、制作者在国际风筝界非常有名、而且在北美和欧洲的国际赛事上多得到过非常好的成绩、他上了年纪还在世界上走动、是个令我尊敬的运动员、我有他一些比赛视频、是个非常令我们这些晚辈们学习的好视频、我们知道的风筝里最出名的风筝就是来自于这个制作室里《机器》不说也知道是谁飞行这款风筝了。好风筝！！！想得到、

LPYCYW

TANTRUM  这款风筝有关数据，做风筝的用到的数据都有，很详细
The Tantrum was designed with the competitor in mind. I have tried to learn from my experiences in
competition and build a kite that not only will perform well in competition but also, would be 􀂳just plain
fun to fly􀂴. A lot of the newer style tricks put a lot of stress on certain areas of the kite. I have taken great
care to reinforce these areas.
The complete trailing edge is hemmed in 3.9 Dacron, doubled in areas of high stress during yo-yo based
tricks.
The bridle is easily replaced without disassembling any part of the kite. Leaders are provided to save
wear on your lines.
A variable weight system is provided to tune the kite to taste or wind conditions. The center brass weight
is 20 gm. The outer steel weights are 5, 10, and 15 gm each. When using the outer weights, place the two
O rings on the spine, above the weights, to help keep them in place.
Upper LE is Skyshark P 200 cut to 71.5 cm
Lower LE is Skyshark P 200 cut to 71.5 cm
Upper spreader is Avia .2200 cut to 46.5 cm
Lower Spreaders are Skyshark 5 PT cut to 71.5 cm.
Spine is Skyshark P200. It is in two pieces. The upper is 71.5 cm and the

lower is 14.5 cm. They are joined by a 2400 ferrule.
Standoffs are .118 microcarbon. Inner is 25 cm and outer is 26 cm not including any fittings
Should you need to remove one of the C-clips or if one should become lost, make sure both sides are
even when replacing with a new part. If you are unable to compare each side, you may measure from the
end of the Leading Edge. Measure up 49 cm from the end of the rod (DO NOT INCLUDE THE NOCK)
to the bottom of the lower APA. This is where the lower fitting goes. The distance between the upper
and lower APAs, center to center, is 64 cm.
The yo-yo stoppers can also be placed using the same method. The distance from the top of the LE to the
stopper is set at 55 cm. This can be adjusted a small amount by sliding the stoppers up or down within the
cutout. In general, if you notice that the kite 􀂳bounces􀂴 while flying in the 􀂳wrapped􀂴 position, raise the
stoppers slightly. Raising them a bit in higher wind can also help reduce some of the stress on the kite
during 􀂳wrapped􀂴 flight.

[ 本帖最后由 LPYCYW 于 2009-3-7 09:10 编辑 ]

捕风

楼上补充的太及时了，如此大篇幅的关于此风筝的介绍真是难得。
如果您能翻译成中文就更好了？这样更加直观便于理解，我想喜欢这款风筝的朋友们一受益匪浅。期待您的翻译。。。。感激不尽！(wanpihou37)

LPYCYW

可别难为我，我也不懂外语，这是我以前的资料，是借助翻译软件猜的，上边杆71.5，下边杆71.5，上横杆46.5，中杆71.5，风道干25和26，配重20克，边杆三通的距离64，其中杆子的规格型号也说的很明白

[ 本帖最后由 LPYCYW 于 2009-3-7 12:58 编辑 ]